IP Office Platform
  Carroll Communications Home
  Avaya IP Office
  Avaya IP Office 406 r2
  Avaya IP Office 412
  IP Office Telephones
  Voice Mail Pro
  Phone Manager Pro
  IP Office Manager
  IP Office Soft Console
  Avaya Conferencing
  Compact Business Center
  Short Codes
  Data Networking
  IP Office Expansion Modules
  IP Office Licenses
  Centrales Telefonicas
  Voice over IP Phone Systems
  IP Office 403

Business Telephones

Telecommunications Consulting
Control Unit
Extension Form Overview
Extension | Extn
Extension | Analog
Extension | VoIP
Extension | IP DECT
User Form Overview
User | User
User | Voicemail
User | DND| Short Codes
User | Source Numbers
User | Telephony
User | Forwarding
User | Dial In
User | Voice Recording
User | Coverage
User | Button Programming
User | Twinning | Menu Programming
User | T3 Options
User | Phone Manager Options
Hunt Group Overview
Hunt Group | Hunt Group
Hunt Group | Voicemail
Hunt Group | Fallback
Hunt Group | Queuing| Voice Recording
Short Code | Short Code
Service Settings Form Overview
Service | Service
Service | Bandwidth
Service | IP
Service | Autoconnect
Service | Quota
Service | PPP
Service | Fallback| Dial In
RAS Form Overview
Incoming Call Route Overview
Incoming Call Route | Standard
WAN Port Overview
WAN Port | Frame Relay
WAN Port | DLCIs
WAN Port | Advanced
Directory | Directory Entry
Time Profile Overview
Firewall Profile Form Overview
Firewall | Custom
IP Route Overview
IP Route | IP Route
RIP Dynamic Routing
Least Cost Routing Overview
Least Cost Routing | LCR| Main Route
Least Cost Routing | Alternate Route
Account Code Overview
Account Code | Voice Recording
License | License
Tunnel | Tunnel (L2TP)
Tunnel | L2TP (L2TP)
Tunnel | PPP (L2TP)
Tunnel | Main (IPSec)
Tunnel | IKE Policies (IPSec)
Tunnel | IPSec Policies (IPSec)
Logical LAN
Wireless Overview
Wireless | Security
User Restrictions Overview
User Rights Overview
User Rights | User
User Rights | Short Codes| Telephony
User Rights | Button/Menu Programming
User Rights | Phone Manager
User Rights | Twinning| Membership
Auto Attendant Overview
Auto Attendant | Auto Attendant
Auto Attendant | Actions
Overview of Authorization Code
E911 System Overview
E911 System | E911 System
E911 System | Zones
IP Office Manager Pt.1
IP Office Manager Pt.3
about us | telephone equipment | t1 lines | partner phone systems | site map | contact us

Avaya IP Office

The Avaya IP Office platform is the ultimate in converged voice and data technology. IP Office brings a combination of voice and data applications formerly reserved for only the largest corporations. Cutting edge customer service with easy to use tools is now available to the smallest of businesses.




WAN Port Overview

These entries are used to configure the operation of IP Office WAN ports. These are the 37-way D-type WAN ports found on the rear of all IP Office control units except the Small Office Edition.

Additional WAN ports can be added by the installation of up to two WAN3 expansion modules, each module providing 3 additional WAN ports. On the Small Office Edition control unit, a single WAN port can be added by the installation of a WAN trunk card at the rear of the unit. For full details of installing additional WAN ports, refer to the IP Office Installation Manual.

Creating a Virtual WAN Port
WAN services can be run over a T1 PRI trunk connection. This requires creation of a virtual WAN port. For full details refer to Using a Dedicated T1/PRI ISP Link in Appendix A.

  1. Select  WAN Port.

  2. Click  and select PPP.  

  3. In the Name field, enter either LINEx.y where:

    • LINE must be in uppercase.

    • x is the line number. For a PRI/T1 module in Slot A, this will be 1. For a PRI/T1 module in Slot B, this will be 5.

    • y is the lowest numbered channel number to be used by the WAN link minus 1. For example, if the lowest channel to be used is channel 1 then y = 1 - 1 = 0.

  4. In the Speed field, enter the total combined speed of the maximum number of channels sets in the Service. In this example, 12 channels x 64000 bits = 76800.

    • Note: The maximum number of channels that can be used will be limited by the number of data channels supported by the IP Office Control Unit and not already in use.

  5. In the RAS Name field, select the RAS name created when the new Service of that name was created.

  6. Click OK.

WAN Port | WAN Port

Use this form to configure the leased line connected to the WAN port on the Control Unit. Normally this connection is automatically detected by the IP Office control unit. If a WAN Port is not displayed, connect the WAN cable, reboot the Control Unit and receive the configuration. The WAN Port configuration form should now be added.



Operator Rights View















IP406 V1



IP406 V2





  • Name
    The physical ID of the Extension port,. This parameter is not configurable; it is allocated by the system.

  • Speed
    The operational speed of this port. For example for a 128K connection, enter 128000. This should be set to the actual speed of the leased line as this value is used in the calculation of bandwidth utilization. If set incorrectly, additional calls may be made to increase Bandwidth erroneously.

  • Mode: Default = SyncPPP
    Select the protocol required:

    • SyncPPP
      For a data link.

    • SyncFrameRelay
      For a link supporting Frame Relay.

  • RAS Name
    If the Mode is SyncPPP, selects the RAS service to associate with the port. If the Mode is SyncFrameRelay, the RAS Name is set through the DCLIs tab.
























































avaya business partner | voice mail | avaya one x quick edition | new phone systems | vm pro | contact us
PO BOX 186 Spring Lake, New Jersey 07762
1-800-429-0077 ::: 732-280-3200
Copyright 2007 CarrollCommunications.com All Rights Reserved.